Message boards :
Number crunching :
Open Beta test: SoG for NVidia, Lunatics v0.45 - Beta6 (RC again)
Message board moderation
Previous · 1 . . . 20 · 21 · 22 · 23 · 24 · 25 · 26 . . . 32 · Next
Author | Message |
---|---|
Keith Myers Send message Joined: 29 Apr 01 Posts: 13164 Credit: 1,160,866,277 RAC: 1,873 |
Note that this means I have nothing else to compare my readings to. I think this is too wide a tolerance for graphic cards under full load to still produce valid results, especially the right-on-the-edge GTX 560. That was certainly the case when I ran a GTX 560. I would be looking closer to a 1.5% tolerance on the +12V rail. This being measured with a multimeter and not depending on a motherboard chipset sensor that can have very large errors depending on how it was setup in calibration by the motherboard vendor. Main thing to measure is the +12V rail NOT under load, that is not crunching, and then under full load of BOINC with whatever tasks per card you are using in your configuration. I would like to see the voltage sag under load. Seti@Home classic workunits:20,676 CPU time:74,226 hours A proud member of the OFA (Old Farts Association) |
Stephen "Heretic" Send message Joined: 20 Sep 12 Posts: 5557 Credit: 192,787,363 RAC: 628 |
Note that this means I have nothing else to compare my readings to. . . Helpful info to have but he won't be testing the 3.3V rail from a molex connector :), nor the negative 5V/12V rails either for that matter. But still good to have for a reference. Stephen . . PS Never try and test a switch mode PSU's voltages without a load, they don't like it and tend to go ... POOF! Just in case you didn't know. [Edit] to clarify that in view of Keith's remark I am talking about no load at all as in not connected to the motherboard or equivalent device, while Keith's comment refers to a nominal load such as a motherboard et al at idle which is safe to do. . |
Grant (SSSF) Send message Joined: 19 Aug 99 Posts: 13855 Credit: 208,696,464 RAC: 304 |
[pre] I've had issues when the error was less than 2%, however in those cases it was due to faulty caps; so lots of noise on the rails & the DC voltage still being pretty close to what it should have been. Lower voltages than specified will generally give more issues than higher voltages for a given deviance from the specified value. eg 12.0V nominal 11.8v is more likely to give problems than 12.2V. EDIT- would be a good idea to monitor the voltages while booting up. Ideally there should be no change from when the system is first turned on to when the desktop is up & BOINC is crunching. Grant Darwin NT |
Stephen "Heretic" Send message Joined: 20 Sep 12 Posts: 5557 Credit: 192,787,363 RAC: 628 |
. . I think you mean deviation, deviance is me on a Saturday night :) Stephen . |
Keith Myers Send message Joined: 29 Apr 01 Posts: 13164 Credit: 1,160,866,277 RAC: 1,873 |
Note that this means I have nothing else to compare my readings to. Good, accurate information. The 3.3V rail is mainly used on the CPU but unfortunately DOES make an appearance on the PCIe slot connector. The -12V rail can mostly be ignored in modern hardware, it only had a use in the RS-232C serial port which has mostly disappeared from current motherboards. Seti@Home classic workunits:20,676 CPU time:74,226 hours A proud member of the OFA (Old Farts Association) |
robertmiles Send message Joined: 16 Jan 12 Posts: 213 Credit: 4,117,756 RAC: 6 |
I finally caught a task postponed by a suspicious spike. [url]http://setiathome.berkeley.edu/result.php?resultid=5166941169 [/url] Appears to have some kind of restart. Mentioned a spike in the output, without mentioning suspicious. |
Zalster Send message Joined: 27 May 99 Posts: 5517 Credit: 528,817,460 RAC: 242 |
I finally caught a task postponed by a suspicious spike. Corrected to make link clickable |
Stephen "Heretic" Send message Joined: 20 Sep 12 Posts: 5557 Credit: 192,787,363 RAC: 628 |
. . Some hardware used +/- 5V to drive their RS232 but the good stuff used the +/- 12V as per the RS232 specs. As you point out, USB has rendered RS232 obsolete unless you really need to interface with older equipment that lacks USB ports. Though even then most would use a USB to RS232 adaptor. Can you think of what else uses the -5V? In any case even the 3.3V on the PCIe slot does not have a major function that I am aware of. Mainly it is the +5V and the +12V that do the heavy lifting. The -5V and -12V only ever had low current ratings as I remember. But for the +5V and +12V better to be a little high than a little low as Grant pointed out. Stephen |
HAL9000 Send message Joined: 11 Sep 99 Posts: 6534 Credit: 196,805,888 RAC: 57 |
There's a suitable power plug or two. I just ordered a multimeter. If you really want to see something scary you should use an oscilloscope to view your power rails at idle & with BOINC running apps. I did that a few years ago on one of my machines. SETI@home classic workunits: 93,865 CPU time: 863,447 hours Join the [url=http://tinyurl.com/8y46zvu]BP6/VP6 User Group[ |
Keith Myers Send message Joined: 29 Apr 01 Posts: 13164 Credit: 1,160,866,277 RAC: 1,873 |
And of course, RS-232 to USB adapters have been the bane of my hobby since I still have to use legacy hardware with serial ports. I typically have 3 in use to drive my scopes, mount and camera interfaces every night. Only in the last couple of years or so have the manufacturers started transitioning to USB or Ethernet interfaces. I believe the -5V and -12V were only used for balanced transmission systems like RS-232 or RS-432 or sometimes in early DC-DC inverters or analog op-amp audio circuits. The ATX12V 1.3 standard dropped the negative rails entirely. Seti@Home classic workunits:20,676 CPU time:74,226 hours A proud member of the OFA (Old Farts Association) |
Stephen "Heretic" Send message Joined: 20 Sep 12 Posts: 5557 Credit: 192,787,363 RAC: 628 |
There's a suitable power plug or two. I just ordered a multimeter. . . I suspect I don't really want to see that :) Stephen . |
jason_gee Send message Joined: 24 Nov 06 Posts: 7489 Credit: 91,093,184 RAC: 0 |
There's a suitable power plug or two. I just ordered a multimeter. Have done it out of curiosity since my now aged Corsair 1200AX PSU came with ferrite chokes on the PCIe power cables. turned out the GTX480 I was running at the time was quite capable of polluting the 12V on the single rail PSU, and the chokes did the trick. Can easily see multi-GPU rigs suffering stability problems without some or another approach to mitigating the noise. While I believe newer GPUs would tend to use higher frequency converters and use less current than a GTX 480, it was a bit of an eyeopener as to the possibilities for subtle system instability, and the importance of quality power. "Living by the wisdom of computer science doesn't sound so bad after all. And unlike most advice, it's backed up by proofs." -- Algorithms to live by: The computer science of human decisions. |
robertmiles Send message Joined: 16 Jan 12 Posts: 213 Credit: 4,117,756 RAC: 6 |
Until the voltmeter arrives, I won't be able to continue the planned tests. So, I've decided to try my other graphics boards in place of the 560 to see if they are also affected by whatever the problem is. |
Stephen "Heretic" Send message Joined: 20 Sep 12 Posts: 5557 Credit: 192,787,363 RAC: 628 |
Until the voltmeter arrives, I won't be able to continue the planned tests. . . A very good idea. That should prove the problem into either the GTX560 or the rig itself. Should have tried that earlier. You may have to reset your fan profile in Afterburner as it will react to the change of GPU. Stephen . |
robertmiles Send message Joined: 16 Jan 12 Posts: 213 Credit: 4,117,756 RAC: 6 |
GTX 560 alternates: I first tried the GTS 450, previously used in the same computer. The software initially thought it was a 9800 GT (the original graphics board for this computer), and BOINC didn't even recognize it as usable. I then tried reinstalling the 362.00 driver; the driver installation program didn't recognize the GTS 450 as compatible with that driver. I then tried installing the oldest driver I already had downloaded, 340.52. It installed, but still considered the board a 9800 GT. I'm out of ideas, so I asked Nvidia. Do you have any other ideas? |
robertmiles Send message Joined: 16 Jan 12 Posts: 213 Credit: 4,117,756 RAC: 6 |
Any other ideas on what to try after that? Looks like I'll need to know what the other wires to the Molex connectors are also. Two black and one red on some, black, brown, and an empty space on others. I've noticed that one of the electrolytic capacitors on the motherboard may be bulging - the top is rounded on that one, but flat on all the others. Not something I can still fix without help, if that's what it is. |
Jimbocous Send message Joined: 1 Apr 13 Posts: 1856 Credit: 268,616,081 RAC: 1,349 |
Any other ideas on what to try after that? "Normal" wiring on a Molex, specifically the larger 4-pin connector used for powering disk drives and the like, is black centers or sometimes a black and a brown (ground), Red (+5v) and Yellow (+12v) to the outsides. Should be able to tell easily with a meter;,nothing will be that far gone. Bulging capacitor tops are usually the kiss of death, and could quite possibly explain your various weirdnesses. I had an old MSI mobo that developed that, and it did begin throwing a lot of error WUs. |
Stephen "Heretic" Send message Joined: 20 Sep 12 Posts: 5557 Credit: 192,787,363 RAC: 628 |
GTX 560 alternates: . . With boards of that era there are some tricky things with drivers, the later drivers don't activate OpenCL on the older cards, nor (on some) the CUDA potential so Boinc will not see it as a viable GPU. There is a message somwhere about what drivers to use for pre-fermi (and maybe early fermi) GPUs. I was crunching for a while on an 8600GT with 256 MB ram. About as minimal as you can get and still crunch with it but I had to use an early driver 337.88. . . I think though that the GTS450 is actually a Fermi card, so I would do a complete uninstall of all video drivers and then try a clean install with the latest driver from Nvidia, it might then see the card for what it is. I use Iobit Advanced system care which has a Power uninstall option that cleans that stuff out pretty well, it removes all traces so the new install should be clean. Stephen . |
Stephen "Heretic" Send message Joined: 20 Sep 12 Posts: 5557 Credit: 192,787,363 RAC: 628 |
Any other ideas on what to try after that? . . On the Molex connector the black wires are ground and the red is +5V while the Yellow is +12 (unless I have misremembered that part :{ ) but the connectors are keyed to avoid issues, that is why they only go in one way. Usually a brown wire is only substituted for a red wire (brown&blue replace red&black respectively due to colour blindness confusion) so I would expect to have brown black black yellow. I don't know why a molex would only have +5V and no +12V. If the molex connectors feeding the adapter for the GPU do not have yellow wires then you have a problem because the purpose of external PCIe power connectors is to provide more power at +12v not +5V. . . If there is a dying cap on the MoBo good luck, replacing them is not fun, and it may be a symptom on something else not right. But caps can get like that just from age, they "dry out" and swell up, then pop eventually. . . Sadly old electronics don't last forever. Stephen . |
Keith Myers Send message Joined: 29 Apr 01 Posts: 13164 Credit: 1,160,866,277 RAC: 1,873 |
Yeah, have to agree about the "kiss of death" regarding bulging capacitors on motherboards. Unlikely too that he will be able to see small ripple voltages with just a simple DVM unless he's ordered a really expensive one which the bulging capacitor almost certainly is producing. If I remember an earlier post correctly, the motherboard is a 1999 Dell vintage. That puts in right at the beginning of the bad capacitor plague caused by the bad stolen industrial espionage electrolyte recipe. Seti@Home classic workunits:20,676 CPU time:74,226 hours A proud member of the OFA (Old Farts Association) |
©2024 University of California
SETI@home and Astropulse are funded by grants from the National Science Foundation, NASA, and donations from SETI@home volunteers. AstroPulse is funded in part by the NSF through grant AST-0307956.