CPU Temp

Message boards : Number crunching : CPU Temp
Message board moderation

To post messages, you must log in.

AuthorMessage
Darth Beaver Crowdfunding Project Donor*Special Project $75 donorSpecial Project $250 donor
Avatar

Send message
Joined: 20 Aug 99
Posts: 6728
Credit: 21,443,075
RAC: 3
Australia
Message 1361083 - Posted: 25 Apr 2013, 15:43:27 UTC

Hi guys my new quad cpu is running temps of
core 1 64c
core 2 53c
core 3 58c
core 4 58c
give or take +- 2c
Could anybody that has a quad tell me if these temps are about right as i'm a little worried I mite not have used enough thermal paste or I have not got the heat sink and fan perfectly seated .The quad is a q8400 and the Tcase temp according to intel is 71.4c
I'm prob worrying over nothing so any advice much appericated
ID: 1361083 · Report as offensive
Alex2
Volunteer tester

Send message
Joined: 2 Nov 12
Posts: 24
Credit: 11,798,226
RAC: 0
Canada
Message 1361095 - Posted: 25 Apr 2013, 16:15:32 UTC - in response to Message 1361083.  
Last modified: 25 Apr 2013, 16:15:50 UTC

Worrying over nothing.
Worry if:
- It goes over 80C (need cleanning).
- A fan stop working.
ID: 1361095 · Report as offensive
Profile James Sotherden
Avatar

Send message
Joined: 16 May 99
Posts: 10436
Credit: 110,373,059
RAC: 54
United States
Message 1361113 - Posted: 25 Apr 2013, 16:43:41 UTC

My I7 920 is running 53 52 51 53 across the cores. My I7 3770 is running 55 54 51 52
[/quote]

Old James
ID: 1361113 · Report as offensive
andybutt
Volunteer tester
Avatar

Send message
Joined: 18 Mar 03
Posts: 262
Credit: 164,205,187
RAC: 516
United Kingdom
Message 1361130 - Posted: 25 Apr 2013, 17:54:13 UTC

Over 70c and I would be getting a little concerned

Andy
ID: 1361130 · Report as offensive
Profile skildude
Avatar

Send message
Joined: 4 Oct 00
Posts: 9541
Credit: 50,759,529
RAC: 60
Yemen
Message 1361174 - Posted: 25 Apr 2013, 20:38:37 UTC
Last modified: 25 Apr 2013, 20:45:07 UTC

I'd be concerned if the CPU is not under a load. An Idle CPU shouldn't get into the mid 40's. I assume you are using a stock HSF.

If you are concerned about the seating, try gently turning the HSF(power off of course) and see if it feels like its stuck in mud. You should get a bit of movement(a few mm side to side) but it should be fill like its stuck in mud


In a rich man's house there is no place to spit but his face.
Diogenes Of Sinope
ID: 1361174 · Report as offensive
Profile Wiggo
Avatar

Send message
Joined: 24 Jan 00
Posts: 36828
Credit: 261,360,520
RAC: 489
Australia
Message 1361176 - Posted: 25 Apr 2013, 20:47:12 UTC - in response to Message 1361083.  

You should be fine with those temps (if that's under full load) and that CPU will start throttling at around 75C anyway, then shut itself down if it necessary.

What HSF are you using on it?

Cheers.
ID: 1361176 · Report as offensive
Darth Beaver Crowdfunding Project Donor*Special Project $75 donorSpecial Project $250 donor
Avatar

Send message
Joined: 20 Aug 99
Posts: 6728
Credit: 21,443,075
RAC: 3
Australia
Message 1361199 - Posted: 25 Apr 2013, 23:00:00 UTC

Sorry no answer straight way was late and crashed

I'm not shore it's name the HSF but the fan is Intell and the heat sink is about 2 x thicker than a normal sink
during the day it's been pushing 66-68 and it's only 1 core that is getting that high the others are about up to 7c lower .
I could not find at intel what temp it burns out only the Tcase 71.4
Wiggo you say it will start throttling at 75 ?? if 75 I can relax
ID: 1361199 · Report as offensive
Darth Beaver Crowdfunding Project Donor*Special Project $75 donorSpecial Project $250 donor
Avatar

Send message
Joined: 20 Aug 99
Posts: 6728
Credit: 21,443,075
RAC: 3
Australia
Message 1361200 - Posted: 25 Apr 2013, 23:02:07 UTC - in response to Message 1361199.  

OH all 4 cores max load plus the gpu max
ID: 1361200 · Report as offensive
Darth Beaver Crowdfunding Project Donor*Special Project $75 donorSpecial Project $250 donor
Avatar

Send message
Joined: 20 Aug 99
Posts: 6728
Credit: 21,443,075
RAC: 3
Australia
Message 1361201 - Posted: 25 Apr 2013, 23:07:23 UTC - in response to Message 1361200.  

The HSF is intel I believe but not standard I had to hunt around to get it this thick
ID: 1361201 · Report as offensive
mramakers

Send message
Joined: 20 Jul 04
Posts: 42
Credit: 3,694,335
RAC: 0
Netherlands
Message 1361666 - Posted: 27 Apr 2013, 5:44:06 UTC - in response to Message 1361083.  

Hi guys my new quad cpu is running temps of
core 1 64c
core 2 53c
core 3 58c
core 4 58c
give or take +- 2c
Could anybody that has a quad tell me if these temps are about right as i'm a little worried I mite not have used enough thermal paste or I have not got the heat sink and fan perfectly seated


Less is better. If too much thermal compound is applied, it will work as an insulator, so less heat will be transferred.
TC is used to smoothen both surfaces because they are not perfectly flat.
ID: 1361666 · Report as offensive
Darth Beaver Crowdfunding Project Donor*Special Project $75 donorSpecial Project $250 donor
Avatar

Send message
Joined: 20 Aug 99
Posts: 6728
Credit: 21,443,075
RAC: 3
Australia
Message 1361671 - Posted: 27 Apr 2013, 5:55:43 UTC - in response to Message 1361666.  

It seems to be ok it's only getting to 67c and that's in the hottest part of the day still getting to 25c and winter on it's way
I only used about harf the TC in the seringe but thank mate
ID: 1361671 · Report as offensive
kittyman Crowdfunding Project Donor*Special Project $75 donorSpecial Project $250 donor
Volunteer tester
Avatar

Send message
Joined: 9 Jul 00
Posts: 51478
Credit: 1,018,363,574
RAC: 1,004
United States
Message 1361680 - Posted: 27 Apr 2013, 6:16:27 UTC - in response to Message 1361671.  
Last modified: 27 Apr 2013, 6:17:41 UTC

It seems to be ok it's only getting to 67c and that's in the hottest part of the day still getting to 25c and winter on it's way
I only used about harf the TC in the seringe but thank mate

I don't know how big the syringe was, but you don't want to apply the stuff like toothpaste.....

On most Intel CPUs, a bead about 1/8" wide by the CPU width is usually plenty, depending on the viscosity of the compound being used. If you are applying a blob the size of a marble to the center of the CPU, you are using WAY too much.

The old 'credit card trick' is the way some used to do it...
Apply the bead at one edge of the CPU and use a credit card with a clean sharp edge to thinly draw it across the surface of the CPU leaving a very thin, even coating. This should be enough if your CPU face and the cooler mating surface are correctly flat.

Install the cooler, maybe give it a slight twist back and forth, and remove the cooler. Check if the paste has been transferred to the entire mating surface of the cooler. If not, either something's not flat, or the cooler is not being properly installed.

If all looks good, you can reinstall the cooler, or better yet, clean it all up with isopropyl alcohol and do it all again. You should then be good to go.

The last few installs I did, I have been using MX-2 paste. It seems to work very well, and has a lower viscosity than many compounds, which allows it to self-spread a bit under the CPU heat and the cooler clamping pressure.
"Time is simply the mechanism that keeps everything from happening all at once."

ID: 1361680 · Report as offensive
Darth Beaver Crowdfunding Project Donor*Special Project $75 donorSpecial Project $250 donor
Avatar

Send message
Joined: 20 Aug 99
Posts: 6728
Credit: 21,443,075
RAC: 3
Australia
Message 1361746 - Posted: 27 Apr 2013, 8:56:08 UTC - in response to Message 1361680.  

MM ok then I have used to much I used about the size if a 5c coin (I think your eqivelent is a dime ) and I used mk2 same as you .I better get more and redo it and hopefully the Temp will go down .
When she is idling it's about 42c the hottest core which I did think was to hot seeing as it has a extra think heat sink . I been expecting it to get a cooler
at night as the temp has been dropping to about 14c but it only drops 2-3 c.
Thank Mark i'm going back to market to exchange the ram as he gave me ram that was too fast for the chip I needed 667mhz he gave me 800 so i'll buy some more TC and do it again.
Good timing mate thanks
ID: 1361746 · Report as offensive
Grant (SSSF)
Volunteer tester

Send message
Joined: 19 Aug 99
Posts: 13855
Credit: 208,696,464
RAC: 304
Australia
Message 1361759 - Posted: 27 Apr 2013, 9:28:34 UTC - in response to Message 1361746.  
Last modified: 27 Apr 2013, 9:29:30 UTC

When she is idling it's about 42c the hottest core which I did think was to hot seeing as it has a extra think heat sink

My i7-2600k is around that temperature at idle, when the ambient temperature is in the mid 30°s, so yeah, it's way too hot.

Been years since i had to refit a heatsink, but i've always done it similary to what msattler said. I'm smear a thin coating of heatsink paste on the CPU & then use a a small piece of plastic with a straight edge (old credit cards are usefull for something) to scrape over the CPU & remove the excess.

The idea of the thermal paste is to fill in the minute air gaps between the CPU & the heatsink. It's not meant to go between the metal of the heatsink & the metal of the CPU, just fill in the (very) tiny gaps.
The heatsink compound transfers heat much better than air does, but not as well as metal to metal contact.
Grant
Darwin NT
ID: 1361759 · Report as offensive
Iona
Avatar

Send message
Joined: 12 Jul 07
Posts: 790
Credit: 22,438,118
RAC: 0
United Kingdom
Message 1361766 - Posted: 27 Apr 2013, 10:03:53 UTC

Yep, Kittyman had this one, spot-on, as one might expect. It may not be much of a 'marker', but on the Q6600, I have occasional use of, the temp spread is from +1 C to +4 C over ambient temperature at idle. Typically, where it operates, that means idling at 30 C - 33 C. However, as per my main, it does not use an Intel HSF....its the OCZ 'clone' of a Scythe Ninja (I use a Ninja 2 with my E8400 - the Ninja 3 is actually identical to a design I came up with about 5 years ago!). If you are using a stock Intel HSF, get rid of it! I'm sure that you'll find plenty of advice here, as to what is better - most are better than an Intel unit, to be honest!



Don't take life too seriously, as you'll never come out of it alive!
ID: 1361766 · Report as offensive
Cruncher-American Crowdfunding Project Donor*Special Project $75 donorSpecial Project $250 donor

Send message
Joined: 25 Mar 02
Posts: 1513
Credit: 370,893,186
RAC: 340
United States
Message 1361959 - Posted: 27 Apr 2013, 21:22:55 UTC

Yes - as far as thermal paste is concerned, use a vanishingly small amount.

Interestingly, I read this several years ago:

http://www.dansdata.com/goop.htm

Even though it is old now, the principles involved still apply.

In fact, I use plain old Vaseline (petroleum jelly) for my thermal goop/grease.

It doesn't evaporate, it stays put, it doesn't clump up or dry out, it is easy to clean up AND it costs next to nothing.

I have used it on all my various crunchers for years with no ill effects, and I run mine 24/7/365.
ID: 1361959 · Report as offensive
Profile Wiggo
Avatar

Send message
Joined: 24 Jan 00
Posts: 36828
Credit: 261,360,520
RAC: 489
Australia
Message 1361986 - Posted: 27 Apr 2013, 22:24:39 UTC - in response to Message 1361959.  

I'm a "long grain rice" person with thermal paste, put only enough paste dead centre about the size of 1 grain of long grain rice then put the HS straight down on it.

Also, those extra hight Intel HSF's were only a few degrees better than the standard 1's, which means they are still not great so looking for something better before next summer would be a good idea.

I've had a Thermaltake Big Typhoon on my Q6600 @ 3GHz since I built it 7yrs ago and it runs 22-26C above ambient under full load on the hottest core (I can't tell you about idle as it rarely is and I've never worried about checking at those rare times).

Cheers.
ID: 1361986 · Report as offensive
kittyman Crowdfunding Project Donor*Special Project $75 donorSpecial Project $250 donor
Volunteer tester
Avatar

Send message
Joined: 9 Jul 00
Posts: 51478
Credit: 1,018,363,574
RAC: 1,004
United States
Message 1362065 - Posted: 28 Apr 2013, 6:09:16 UTC - in response to Message 1361986.  

I'm a "long grain rice" person with thermal paste, put only enough paste dead centre about the size of 1 grain of long grain rice then put the HS straight down on it.

Also, those extra hight Intel HSF's were only a few degrees better than the standard 1's, which means they are still not great so looking for something better before next summer would be a good idea.

I've had a Thermaltake Big Typhoon on my Q6600 @ 3GHz since I built it 7yrs ago and it runs 22-26C above ambient under full load on the hottest core (I can't tell you about idle as it rarely is and I've never worried about checking at those rare times).

Cheers.

I'm still running 6 Thermaltake Big Typhoon coolers here. Most with upgraded fans.
"Time is simply the mechanism that keeps everything from happening all at once."

ID: 1362065 · Report as offensive

Message boards : Number crunching : CPU Temp


 
©2024 University of California
 
SETI@home and Astropulse are funded by grants from the National Science Foundation, NASA, and donations from SETI@home volunteers. AstroPulse is funded in part by the NSF through grant AST-0307956.