Transmission Issues

Morning all ...

I've not been able to send my result files in since August 6th, and some of them are at or pass the report
deadline.

Is there some issue right now that is preventing the
server from receiving data ?

Ref:

BOINC 6.10.58 / Seti@Home Enhanced 6.03

Error Message(s - This is all I've gotten since the 6th - 10 Files Backed up now)

Started upload of 22ap10ae.28321.16427.11.10.130_0_0
Temporarily failed upload of 22ap10ae.28321.16427.11.10.130_0_0: HTTP error
Backing off 2 hr 41 min 16 sec on upload of 22ap10ae.28321.16427.11.10.130_0_0

Thanks all


____________

Currently, the SETI servers are down, see the homepage news, but you should be able to upload from Friday to Monday.

Did you reboot your computer during that time? Sometimes buffers have to be cleared.

If you still can't upload on Friday or Saturday, you should post here again.

Gruß,
Gundolf
____________
Computer sind nicht alles im Leben. (Kleiner Scherz)

SETI@home classic workunits 3,758
SETI@home classic CPU time 66,520 hours

Was refused permission to post to an existing thread on the Science (non-SETI) message board. The reason given was that I had to have a certain number of credits before being allowed to do so. Accessed my account; it reports that I have over 78,000 credits. The system also says that I'm trying to start a new thread, which I'm not. Have not run into this problem before, have posted many times to message boards. Any ideas on how to solve this problem? Thanks. P.S. I see that my post to this thread was accepted, so the problem appears to be limited in scope. I was also refused posting access to the SETI Science board. Michael

The message you get is a bit incorrect. It's recent average credit that you need. Yours is zero, or close to zero at the moment. You need a RAC of one or more to be able to post in the main forums.

This was added as a guard against spammers and trolls. The Q&A forums are open to all, as usually when you have problems with Seti, you will not have credit (and thus RAC) either.

So, in order for you to be able to post on the main forums, you'll have to allow work, get it, crunch it, upload it and report it, then wait until it's validated against someone else.
____________
Jord

- BOINC FAQ Service
- BOINC User Wiki

Real is just a matter of perception.

Ageless;Thanks for your reply. I began to suspect that this was an issue over RACs rather than total credits. I have been trying to resolve the problem of not processing work units for some time. Contacted several of the volunteer troubleshooters about this, but none replied. My screensaver is frozen in the middle of processing two different work units, and says paused, user active. I don't have my preferences set to cease processing, when I'm active, so I don't really understand this. Any ideas on how to end the pause and begin processing work units again? Thanks. Michael

Do you use the web preferences or local preferences?

The local preferences override the web preferences. So changing anything on the web preferences will then not help you much (or at all). Please check what's set in BOINC Manager->Advanced view->Advanced->Preferences, processor tab. If "While computer is in use" is not checked, then this will be the culprit.
____________
Jord

- BOINC FAQ Service
- BOINC User Wiki

Real is just a matter of perception.

Just to add to what Ageless said, if you don't want to use the local preferences through the BOINC Manager but you check in there exit by using the clear button. If you exit using the ok or even the red X it could cause some settings to be activated if they were marked or showed as different from the web based preferences.
____________


PROUD MEMBER OF Team Starfire World BOINC

Thank you, Ageless, perryjay, and John Mc Leod VII, for your helpful advice. My computer is now processing work units again. Michael