Message boards :
Number crunching :
just want to know ......
Message board moderation
Author | Message |
---|---|
gorak Send message Joined: 9 Jun 04 Posts: 8 Credit: 9,843 RAC: 0 |
do u people get WU ? loaded setiboinc 3.20 and now i just get SETI@home - 2004-07-15 21:42:16 - Sending request to scheduler: http://setiboincdata.ssl.berkeley.edu/sah_cgi/cgi SETI@home - 2004-07-15 21:42:23 - Scheduler RPC to http://setiboincdata.ssl.berkeley.edu/sah_cgi/cgi succeeded Nothing further . is this right for now (project off?) or is there problems with my settings ? |
Thierry Van Driessche Send message Joined: 20 Aug 02 Posts: 3083 Credit: 150,096 RAC: 0 |
One thing that might help is go to "Your Account" and there go to "General Preferences". Choose Keep enough work on disk to last between and set the values between 2 and 3 days. Back to your GUI, choose the tab "Projects" and right click with the mouse to use "Update". This should update your new settings on your client. Hope this helps. Greetings from Belgium. |
CyberGoyle Send message Joined: 2 Jun 99 Posts: 160 Credit: 3,622,756 RAC: 26 |
Most everyone is getting work units fine. If you having problems, make sure your cache preferences are high enough for your PC (for instance, I have a 200mhz PC that takes about 6 days to finish a workunit - the default cache setting of 3 days prevented me from getting workunits on that PC). Make sure you update your preferences on the BOINC client after you make changes on the web interface. If that doesn't help, verify that the client doesn't actually have any workunits. You can see them in the 'Work' tab. Sorry if that seems obvious, but I do helpdesk work - you'd be surprised. Hope I gave you some ideas. <a> |
Darren Send message Joined: 2 Jul 99 Posts: 259 Credit: 280,503 RAC: 0 |
> loaded setiboinc 3.20 and now i just get > SETI@home - 2004-07-15 21:42:16 - Sending request to scheduler: > http://setiboincdata.ssl.berkeley.edu/sah_cgi/cgi > SETI@home - 2004-07-15 21:42:23 - Scheduler RPC to > http://setiboincdata.ssl.berkeley.edu/sah_cgi/cgi succeeded Are you attached to any other projects (such as predictor@home) or only seti? If you are attached to something else, it's just waiting for a low water mark. If not, there should be more after the "succeeded" message. |
CyberGoyle Send message Joined: 2 Jun 99 Posts: 160 Credit: 3,622,756 RAC: 26 |
LOL, same answer within 7 seconds! |
Christopher Hauber Send message Joined: 10 Feb 01 Posts: 196 Credit: 71,611 RAC: 0 |
Looks ok. It should download automatically after it sits there for a minute or two based on your account settings. I just downloaded some workunits a few minutes ago and it worked fine so if it went down it just went down. I'm also still running 3.19 but I don't THINK that would cause a difference. Check your settings and let it sit a bit. If it still does nothing, do a manual update (projects tab, right click, select update now). Chris > do u people get WU ? > loaded setiboinc 3.20 and now i just get > SETI@home - 2004-07-15 21:42:16 - Sending request to scheduler: > http://setiboincdata.ssl.berkeley.edu/sah_cgi/cgi > SETI@home - 2004-07-15 21:42:23 - Scheduler RPC to > http://setiboincdata.ssl.berkeley.edu/sah_cgi/cgi succeeded > > Nothing further . is this right for now (project off?) or is there problems > with my settings ? > > > |
gorak Send message Joined: 9 Jun 04 Posts: 8 Credit: 9,843 RAC: 0 |
i detached again ..... and attached . got some WU now downloading . thanks |
©2024 University of California
SETI@home and Astropulse are funded by grants from the National Science Foundation, NASA, and donations from SETI@home volunteers. AstroPulse is funded in part by the NSF through grant AST-0307956.